![play the sims 1 online play the sims 1 online](https://www.firestormgraphix.com/media/catalog/product/cache/1/image/17f82f742ffe127f42dca9de82fb58b1/s/p/speedway-street-stoick.jpg)
Rear bumper not covered must have rounded ends that are connected to the body or the frame. Aftermarket plastic nose and tail pieces ok. Front bumper must be OEM with no sharp edges. Maximum 18″ from front of brace to rear of body. Maximum 4 braces including side braces: maximum 3″material height at front and must run in straight line to a maximum 7″ material height at rear.
#PLAY THE SIMS 1 ONLINE DRIVER#
Back of hood must be sealed off from driver compartment. Aluminum body allowed but must resemble stock OEM pieces. All holes in front and rear firewall are to be covered in metal or aluminum plating. Minimum 12″ vertical opening to left and right sides. Must have windshield pillars, painted roll bars are not acceptable.
#PLAY THE SIMS 1 ONLINE WINDOWS#
All windows must remain open, except opera windows Maximum 7″ visor may be added to top of windshield opening. Driver side door plate constructed of 18 gauge or 0.049 inch minimum thickness steel is highly recommended. Minimum of four uprights tied from frame to top door bar on driver side, three on passenger side. Three horizontal door bars on both sides are mandatory and must be welded to the front and rear roll cage members. tubing and must have a wall thickness of. Must be as parallel with the ground as possible and located perpendicular to the driver so as to provide maximum protection for driver without causing undue difficulty in getting into or out of vehicle. Must have minimum of three windshield bars in front of driver. May have two bars for protection in front of radiator, behind bumper within confines of body, no wider than stock frame horns. Tubing may be added from top of roll cage to rear frame section to protect fuel cell. May have front hoop from roll cage forward to protect radiator. Must have minimum of one cross bar in the top of halo of roll cage. On uni-body cars, cage will be mounted to four 1/4″ plates and mounted to the floor with four 1/2″ bolts per plate. Top halo must be no less than 40″ across, inside to inside. Location: No more than 41″ from top center of windshield to front edge of rear hoop. Must be electric welded and well constructed. Other materials are subject to prior approval. Low carbon, mild steel tubing is recommended. seamless tubing and must have a wall thickness of. Material must not be less than 1.625″ O.D. Rub rails no bigger than 1″ by 2″ may be attached to the body from fender well to fender well and rear quarter panel, flush with body and painted to match car.Īll cars must have minimum 4 point roll cage. Minimum 108″ wheelbase, maximum 1” difference from side to side.
#PLAY THE SIMS 1 ONLINE FULL#
manufactured full body rear wheel drive passenger car with full frame or uni-body. Leaving tech area without Tech or other Track Officials approval will result in a disqualification.Īny U.S. Must have an additional master shut off switch mounted BEHIND driver seat on horizontal surface (floor is not acceptable), clearly marked “on/off”, and be easily accessible from outside of car. Kill switch to be mounted within easy reach of driver and clearly marked “on/off”. 25″ by 2″ steel mounted 6″ from the front of the driveshaft. 360 degree driveshaft loop required and must be constructed of at least. Aluminum racing seats only and must be securely fastened to roll cage. Five point safety harness is required and must be securely mounted to roll cage using 1/2″ diameter bolts. Window net to be mounted so latch is at the top front of window.
![play the sims 1 online play the sims 1 online](https://i.ytimg.com/vi/8ot5M94WACU/maxresdefault.jpg)
16X20 driver side ribbon or mesh type window net or arm restraints required. SFI approved full fire suits, fire retardant neck braces and gloves are required. Helmets must be worn at all times including packing.
![play the sims 1 online play the sims 1 online](https://s100.iracing.com/wp-content/uploads/2017/02/ON-FANATEC-Street-Stock-Rookie-Series-1.jpg)
Required helmets must be Snell SA2000, SFI 31.1/2005 or newer.